Home Guides iPhone 17e iPhone 17e Microphone Replacement

iPhone 17e Microphone Replacement

This document provides instructions for substituting the microphone component within an iPhone 17e.
  • Voice recognition problems or sporadic malfunctions that persist even after a device reset suggest a potential microphone failure requiring replacement.The microphone addressed in these instructions represents one of three distinct microphone components; it's designed for individual replacement.The charging port assembly incorporates a separate microphone, while another is built into the power button assembly.
  • Securing the replacement back glass necessitates the use of replacement back glass adhesive.Should your newly installed microphone lack pre-applied adhesive, you must also obtain replacement microphone adhesive.Visual differences may be present in the accompanying images, as they originate from a different iPhone model, but these variations will not impact the repair steps.
Despite these visual differences, the outlined procedure remains applicable.

Step 1 | Before you begin

Step 1 image
Thumbnail 1
Thumbnail 2
To mitigate potential hazards, ensure the phone's battery is discharged to a level below 25%, given the inherent risks associated with charged lithium-ion cells.Disconnect all connected cables from the device prior to commencing the repair process.
  • Initiate the power-off sequence by concurrently depressing the power button and a volume button, subsequently sliding to deactivate the phone.
  • Simultaneous pressure on the power button and a volume button, followed by a sliding motion, is required to completely shut down the device.

Step 2 | Tape over any cracks

Step 2 image
Thumbnail 1
Thumbnail 2
Significant damage, such as extensive cracks, to either the display panel or rear glass necessitates immediate protective measures.To safeguard against injury and ease the subsequent separation process, affix multiple layers of adhesive packing tape across the damaged surfaces.
  • A sufficiently sized, uninterrupted section of the lower edge is required to allow for secure attachment of a suction cup.

Step 3 | Remove the pentalobe screws

Step 3 image
Thumbnail 1
Thumbnail 2
Employ a pentalobe P2 screwdriver for the disassembly process.Two fasteners, each measuring 7.8 millimeters in length, must be detached.These screws are situated on both lateral aspects of the charging port.Proper tool selection is essential to avoid damage during screw removal.

Step 4 | Mark your opening picks

Step 4 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
Preventing harm to your device necessitates careful pick insertion, as excessive depth can cause damage.The subsequent instructions detail the procedure to ensure proper pick depth.
  • Establish a reference point by measuring precisely 3 millimeters.Utilize a permanent marker to indicate the 3-millimeter point on the opening pick.For enhanced precision, consider marking additional corners of the pick with varying measurement values.
  • As an alternative method for depth control, affix a coin to the pick's tip.
  • Secure the coin to the pick at a distance of 3 millimeters from the tip.This coin attachment serves as a visual depth gauge during the opening process.Adhering to these guidelines minimizes the risk of device damage during the initial opening phase.

Step 5 | Heat the bottom edge

Step 5 image
  • Utilize a heated iOpener on the lower perimeter of the rear glass panel, maintaining application for 90 seconds.As an alternative method, a hair dryer or heat gun can be employed to warm the lower edge of the back glass until a noticeable temperature is felt.Exercise care to prevent excessive heat exposure, as the internal battery is susceptible to thermal degradation.
  • The application of heat should be focused solely on the lower edge to facilitate separation of the back glass.
  • Prolonged or intense heating may compromise the battery's structural integrity and operational lifespan.

Step 6 | Insert an opening pick

Step 6 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  1. Securely attach a suction cup to the lower border of the rear glass assembly.
  2. Exert a consistent, considerable upward pull on the suction cup to generate separation between the rear glass and the device's frame.
  3. Carefully introduce the pointed end of a prying tool into the newly formed space.

Step 7 | Back glass information

Step 7 image
  1. Carefully sever the adhesive bonds holding the rear glass in place, ensuring your tool does not penetrate beyond a depth of 3 millimeters.Exceeding this 3-millimeter depth poses a risk of component damage.A fragile cable, responsible for communication between the back glass assembly and the device's internal circuitry, is situated near the volume up button and must be protected.
  2. Numerous spring contacts, forming a sealed perimeter around the phone's frame, are also vulnerable to accidental damage.
  3. Exercise caution during this process to prevent injury to these sensitive areas.

Step 8 | Separate the bottom adhesive

Step 8 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  1. Utilize a separation tool inserted beneath the rear glass to sever the adhesive bond along its lower edge.
  2. Maintain the positioning of the separation tool close to the lower-left corner for subsequent steps.

Step 9 | Heat the left edge

Step 9 image
  • To initiate separation, utilize a heated iOpener on the left side of the rear glass panel, maintaining heat for a duration of 90 seconds.Employing a hair dryer or heat gun, ensure the rear glass reaches a temperature where it feels hot upon contact.The purpose of applying heat is to soften the adhesive securing the back glass.
  • Prolonged or excessive heat application should be avoided to prevent damage to underlying components.

Step 10

Step 10 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Employ a specialized opening pick, pivoting it near the lower-left section, and move it along the left side to detach the adhesive bond and disengage the metal fasteners.
  • Audible and tactile confirmation of the metal clip disengagement will occur as the pick traverses their locations.
  • Maintain the positioning of the opening pick close to the upper-left area after the separation process.

Step 11 | Heat the top edge

Step 11 image
Employ an iOpener device against the upper border of the rear glass panel, maintaining contact for a duration of 90 seconds.Utilize a hair dryer or heat gun to warm the rear glass surface until it reaches a temperature that is perceptible upon touch.
The application of heat facilitates separation of the rear glass from the device's chassis.

Step 12 | Separate the top adhesive

Step 12 image
Thumbnail 1
Thumbnail 2
  • Employ a specialized opening pick, pivoting it near the upper-left corner, then maneuvering it along the top perimeter to detach the adhesive bond and disengage the metal retaining clips.
  • Audible and tactile confirmation of the metal clips' disengagement will occur during their passage.
  • Maintain the positioning of the opening pick within the upper-right corner.

Step 13 | Heat the right edge

Step 13 image
  • To initiate separation, position the iOpener tool against the right vertical edge of the rear glass assembly and maintain pressure for a duration of 90 seconds.Employing either a hair dryer or a heat gun, apply warmth to the exterior surface of the back glass until it reaches a temperature that is perceptible upon contact.
  • The purpose of applying heat is to soften the adhesive securing the back glass, facilitating its detachment from the device's frame.

Step 14 | Separate the right adhesive

Step 14 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • To prevent potential harm to the concealed wiring, ensure the insertion depth of the tool remains at or below a 3-millimeter limit.
  • By pivoting the opening tool near the upper-right corner and moving it along the right side, the remaining adhesive can be detached from the metal clip; a distinct audible and tactile indication will signal the clip's disengagement as it is passed.

Step 15

Step 15 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Ensure the adhesive securing the rear glass has been fully detached; should any residual adhesive remain, maneuver a separating tool along the perimeter of the rear glass to achieve complete separation.
  • Carefully pivot the rear glass assembly away from the device's body, positioning it vertically against a stable and uncontaminated surface to prevent damage.

Step 16 | Remove the lower connector cover screws

Step 16 image
Thumbnail 1
Thumbnail 2
  • Utilize a specialized Y000 tri-point screwdriver for disassembly.The lower connector cover is fastened with two screws, each measuring 1.3 millimeters in length, requiring their removal.

Step 17 | Remove the battery bracket

Step 17 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Employing tweezers or manual dexterity, carefully raise the lower connector cover and advance it upwards along the device's chassis to disengage it from the securing metal clip.The lower connector cover's release from the metal clip necessitates a sliding motion towards the phone's upper portion.To facilitate access to the connectors beneath, the lower connector cover must be detached.
  • A specialized tool, such as tweezers, or direct finger manipulation can be utilized to achieve the removal of the lower connector cover.

Step 18 | Disconnect the battery

Step 18 image
Thumbnail 1
Thumbnail 2
  • Employing the tip of a spudger, carefully lift and detach the battery press connector.

Step 19 | Remove the middle connector cover screw

Step 19 image
Thumbnail 1
Thumbnail 2
Utilize a specialized Y000 tri-point screwdriver for disassembly.A diminutive, 1.0 millimeter screw is present and requires careful handling.This screw serves the purpose of fastening the middle connector cover in place.Proper application of the Y000 screwdriver is necessary to detach the cover.

Step 20 | Remove the middle connector cover

Step 20 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • The central connector cover secures itself within two metallic fasteners, one positioned above and the other below.
  • Employ the tip of a spudger tool to gently displace the middle connector cover downward, disengaging the retaining clips.
  • Alternatively, utilize a pair of tweezers or your fingertips for the subsequent removal process.Carefully extract the cover following the clip release.Ensure complete detachment of the component from its mounting points.

Step 21 | Disconnect the wireless charging coil

Step 21 image
Thumbnail 1
Thumbnail 2
The wireless charging coil press connector facilitates electrical connection to the charging coil.
  • Employing the tip of a spudger, carefully lift and separate the wireless charging coil press connector to release its connection.

Step 22 | Remove the back glass

Step 22 image
The rear panel, commonly referred to as the back glass, requires separation from the device's frame.
  • Carefully detach the back glass component from the surrounding frame structure to facilitate its removal.

Step 23 | Remove the Taptic Engine connector cover screws

Step 23 image
Thumbnail 1
Thumbnail 2
The Taptic Engine connector cover is held in place by fasteners.
  • Employ a Phillips-head screwdriver to detach the two screws.Each screw measures precisely 2.2 millimeters in length.These screws secure the Taptic Engine connector cover for access.

Step 24 | Remove the Taptic Engine connector cover

Step 24 image
Thumbnail 1
Thumbnail 2
The Taptic Engine connector cover requires detachment for access.
  • Employing tweezers or manual dexterity, carefully disengage the component.The part designated as the Taptic Engine connector cover is the subject of this removal procedure.This action concludes the removal of the Taptic Engine connector cover.

Step 25 | Disconnect the Taptic Engine

Step 25 image
Thumbnail 1
Thumbnail 2
The Taptic Engine press connector requires disconnection using a specialized tool.
  • Employing the pointed end of a spudger, carefully lift and separate the Taptic Engine press connector.

Step 26 | Remove the Taptic Engine screw

Step 26 image
Thumbnail 1
Thumbnail 2
Utilize a Phillips screwdriver to detach the screw, measuring 2.1 millimeters in length, which fastens the Taptic Engine.The screw's diminutive size, at 2.1 mm, necessitates careful handling with a Phillips screwdriver to avoid stripping the head.A Phillips screwdriver is essential for loosening the 2.1 mm screw that holds the Taptic Engine in place.Employing a Phillips screwdriver, carefully unscrew the fastener, noting its short length of 2.1 mm, to access the Taptic Engine.

Step 27 | Remove the Taptic Engine

Step 27 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
Employ the pointed end of a spudger to gently disengage the Taptic Engine from its housing.Continue prying with the spudger until the Taptic Engine is accessible for manual grasping.Once sufficient clearance is achieved, secure a firm hold on the Taptic Engine with your fingers.The Taptic Engine is now free from its mounting within the device frame.Proceed to completely detach the Taptic Engine from the assembly.
This action fully separates the Taptic Engine component.Ensure the Taptic Engine is completely removed from the device's internal structure.The Taptic Engine has been successfully extracted.

Step 28 | Remove the loudspeaker screws

Step 28 image
Thumbnail 1
Thumbnail 2
Employ a Phillips head screwdriver for the task of detaching the four screws that hold the loudspeaker in place.The loudspeaker is fastened with two screws, each measuring 1.4 millimeters in length.
  • Two additional screws, each with a length of 1.7 millimeters, are also present.
  • A tri-point screwdriver, specifically a Y000 type, is necessary to extract the screw that has a 1.3-millimeter length.
  • The removal of the loudspeaker's securing screws requires the use of a Phillips screwdriver.

Step 29 | Remove the loudspeaker

Step 29 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Employ the tip of the spudger to carefully disengage the loudspeaker from its housing, facilitating its removal.The loudspeaker's extraction from the frame is achieved by leveraging the spudger's pointed end.To detach the loudspeaker, utilize the spudger's point and apply gentle lifting force to separate it from the frame.

Step 30 | Loudspeaker gasket information

Step 30 image
Thumbnail 1
Thumbnail 2
  • Should the orange loudspeaker gasket become dislodged during the disassembly process, utilize tweezers for its reinstallation within the sound channel.Employing tweezers is necessary to correctly position the orange loudspeaker gasket back into its designated location inside the sound channel, if it was removed previously.To reinstall a loudspeaker gasket that detached during disassembly, carefully manipulate it back into the sound channel using tweezers.

Step 31 | Lift the screw cover

Step 31 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Employ the planar edge of a spudger to wedge between the microphone's protective cover and its housing.
  • Rotate the spudger to sever the adhesive bond securing the cover, simultaneously disengaging its integrated metal fastener.
  • Apply slight upward pressure with a fingertip to flex the cover, exposing the remaining standoff screw situated above.

Step 32 | Remove the microphone screws

Step 32 image
Thumbnail 1
Thumbnail 2
  • Employ a standoff screwdriver to detach the two screws that hold the microphone in place.
  • The first screw is of a 3.0 mm length.
  • The second screw measures 2.8 mm in length.
  • Utilize a tri-point Y000 screwdriver to unscrew the 1.3 mm screw that fastens the microphone.

Step 33 | Remove the microphone

Step 33 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Employing the broad, planar tip of a spudger, elevate the microphone to a point where it can be securely held by hand.The spudger's flat end facilitates lifting the microphone component.Sufficient vertical displacement is required to permit manual grasping of the microphone.

Step 34

Step 34 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • To facilitate adhesive separation, carefully detach the microphone assembly from the frame.
  • Proceed with the removal of the microphone component.

Step 35 | End of disassembly

Step 35 image

Having finished the device's disassembly, the subsequent instructions detail the reassembly procedure.

Step 36 | Remove the old adhesive

Step 36 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
To eliminate existing adhesive, proceed with removal.
  • Employing tweezers or manual dexterity, detach the aged adhesive material affixed to the underside of the frame.The frame's surface should now be free of the old adhesive.Should any adhesive remnants persist on the frame, a cleaning process is required.
  • Utilize a high-concentration isopropyl alcohol solution, exceeding 90% purity, alongside a coffee filter or a lint-free cloth for effective cleaning.The solvent's strength ensures thorough residue dissolution.This cleaning action will restore the frame's surface to a pristine condition.

Step 37 | Remove the white liner

Step 37 image
Thumbnail 1
Thumbnail 2
  • Microphones pre-equipped with adhesive require bypassing the subsequent two procedures.
  • Maintain secure contact with the microphone's adhesive surface using manual pressure or tweezers, then peel away the white protective backing.

Step 38 | Apply the adhesive to the microphone

Step 38 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Orient the microphone during handling, ensuring the metallic portion is positioned above.
  • Secure the adhesive to the microphone's surface, maintaining the upward orientation of the release tab.

Step 39

Step 39 image
Thumbnail 1
Thumbnail 2
  • Carefully detach the microphone's adhesive backing by removing the blue liner.

Step 40

Step 40 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • To ensure a secure bond, position the microphone with a downward tilt, allowing the adhesive to make full contact with the surrounding frame of the sound channel.
  • Apply consistent pressure to the microphone to guarantee proper adhesion within its designated location.

Step 41 | Install the microphone screws

Step 41 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
The microphone component requires installation.
  • Employing a standoff screwdriver, affix the microphone to the device's structure with two screws while maintaining contact between the microphone and the frame.
    • A screw measuring 3.0 millimeters in length is needed for this step.Additionally, a screw with a length of 2.8 millimeters is also required.
    • A tri-point Y000 screwdriver is necessary to fasten the subsequent screw.The next screw to be installed has a length of 1.0 millimeter.
  • This final screw secures the microphone's position.Ensure proper alignment during installation to prevent damage.Carefully tighten each screw to the appropriate torque to avoid stripping the threads.

Step 42 | Connect the microphone

Step 42 image
A spudger is required for this procedure.
  • Employ the spudger's planar tip to establish a connection with the microphone press connector.

Step 43 | Connect the screw cover

Step 43 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
Secure the screw cover in position.
  • Apply pressure with a fingertip to re-seat the screw cover.

    Confirmation of proper engagement will be indicated by an audible and tactile "click".
    Should the adhesive residue on the screw cover lack sufficient tackiness, substitute it with a segment of double-sided adhesive tape, such as Tesa Tape.

Step 44 | Install the loudspeaker

Step 44 image
Thumbnail 1
Thumbnail 2
To install the loudspeaker, carefully position it within the designated opening in the frame.
  • Ensure the loudspeaker is properly seated within its cutout during placement.

Step 45 | Install the loudspeaker screws

Step 45 image
Thumbnail 1
Thumbnail 2
The loudspeaker is affixed with screws.
  • Employ a Phillips screwdriver to fasten the loudspeaker in place with five screws.
    • Two screws, each measuring 1.4 millimeters in length, are required.Additionally, two screws with a length of 1.7 millimeters must be utilized.
    • A single screw, measuring 1.3 millimeters in length, is also needed.For the 1.3 mm screw, a specialized tri-point Y000 screwdriver is essential.
    • Properly securing the loudspeaker necessitates the use of these specific screw lengths.Ensure the correct screwdriver type is used to prevent damage to the screw heads.

Step 46 | Place the Taptic Engine

Step 46 image
Thumbnail 1
Thumbnail 2
Secure the Taptic Engine component within its designated recess on the device's structural frame.Ensure proper alignment and placement of the Taptic Engine within the frame's corresponding aperture.

Step 47 | Install the Taptic Engine screw

Step 47 image
Thumbnail 1
Thumbnail 2
Employ a Phillips screwdriver for the installation process of the screw.The screw's length is precisely 2.1 millimeters.This fastener's purpose is to secure the Taptic Engine.The Taptic Engine is held in place by the screw.A Phillips screwdriver is required for the screw's installation.
  • The screw, measuring 2.1 millimeters in length, is used.The Taptic Engine is fastened with the screw.The screw's function is to maintain the Taptic Engine's position.Utilize a Phillips screwdriver to affix the screw.The Taptic Engine's attachment is achieved via the 2.1 mm screw.

Step 48 | Connect the Taptic Engine

Step 48 image
Employ the planar edge of a spudger tool to engage the Taptic Engine press connector.
  • Utilize the flat surface of a spudger to establish a connection with the Taptic Engine press connector.

Step 49 | Install the Taptic Engine connector cover

Step 49 image
Thumbnail 1
Thumbnail 2
  • Position the cover component directly atop the Taptic Engine connector.

Step 50

Step 50 image
Thumbnail 1
Thumbnail 2
  • Employ a Phillips screwdriver for the installation process.The screws, each measuring 2.2 millimeters in length, require a Phillips screwdriver for secure fastening.To affix the Taptic Engine connector cover, utilize a Phillips screwdriver.Secure the Taptic Engine connector cover by installing the two screws, which have a length of 2.2 mm, with a Phillips screwdriver.A Phillips screwdriver is necessary to install the two 2.2 mm screws that hold the Taptic Engine connector cover in place.

Step 51 | Remove the residual frame adhesive

Step 51 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Employing tweezers facilitates the removal of adhesive material encircling the frame's edges.Prior to grasping the adhesive with tweezers, it might be necessary to gather it into a concentrated form using the tip of a spudger.Residual adhesive can be effectively eliminated by wiping with a coffee filter or a lint-free cloth saturated with isopropyl alcohol exceeding 90% concentration.
    The tweezers should be utilized to grip and detach the adhesive, which often requires initial manipulation with a spudger.
    To ensure a clean surface, meticulously clean any remaining adhesive traces with a coffee filter or a lint-free cloth dampened with isopropyl alcohol having a purity greater than 90%.

Step 52 | Orient the adhesive

Step 52 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Position the new adhesive onto the frame, ensuring the wider blue protective liner faces inward and the removal tab is situated in the lower-right area.
    Variations in liner color and pull tab placement are possible depending on the specific adhesive model.
    Employ existing frame details, like the camera aperture and edge indentations, to guide proper adhesive placement within the frame.

Step 53 | Apply the adhesive

Step 53 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • After applying pressure to secure the adhesive, any adjustments to its placement are impossible.Attempting to shift the adhesive necessitates complete removal and replacement with a fresh strip.Initiate the peeling process of the adhesive's backing liner using the provided pull tab, commencing from the lower edge, but avoid complete removal.Maintain the blue liner's position away from the work area while precisely aligning the adhesive’s bottom edge with the corresponding edge of the iPhone.Ensure proper alignment of the iPhone’s spring contacts with the liner’s openings as you seat the adhesive’s lower edge into the frame's designated channel.

Step 54

Step 54 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Progressively remove the protective liner from the adhesive strip, ensuring firm contact with the iPhone’s frame edges as you apply it.Proper alignment of the lower edge will automatically position the side and top edges correctly.Should misalignment occur, discard the adhesive and reapply a fresh strip; however, if a replacement is unavailable, the iPhone can be temporarily reassembled and used without adhesive, acknowledging a reduction in water resistance until a new adhesive strip is installed.

Step 55 | Press the adhesive into place

Step 55 image
Thumbnail 1
Thumbnail 2
  • Employ the planar edge of a spudger tool to secure the adhesive bond by applying pressure along the frame's outer boundary.The adhesive's adhesion can be improved by using the flat spudger end to apply even pressure around the entire frame edge.To ensure a secure bond, utilize the flat portion of a spudger to firmly seat the adhesive along the frame's circumferential edge.

Step 56

Step 56 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
Employ a spudger tool for the subsequent step.
  • The pointed end of the spudger should be utilized to elevate the pull tab.Locate the pull tab situated in the upper-right section of the pink adhesive liner.Once the tab is raised sufficiently with the spudger, secure it with your fingers.

Step 57

Step 57 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
Grasp the designated pull tab firmly.
  • Employ the pull tab to separate the pink protective liner from the frame's adhesive surface, thereby revealing the underlying blue liners.

Step 58 | Connect the press connectors

Step 58 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
The rear enclosure's glass component requires repair.
  • Employ a stable platform, such as a box, to elevate the rear glass along the device's right side, maintaining its position.
  • Establish contact with the charging coil's connector and subsequently the battery connector utilizing the broad tip of a spudger tool or a fingertip.

Step 59 | Place the middle connector cover

Step 59 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
Position the intermediate connector cover atop the wireless charging coil, ensuring a slight projection beyond the logic board's lower clip aperture to facilitate secure attachment.
  • The cover's placement should allow a small amount of overhang relative to the slot on the logic board, specifically designed to engage with the bottom clip.

Step 60

Step 60 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
The logic board is the component needing attention.
  • Apply downward force to the cover utilizing a fingertip to secure its position on the logic board.
  • Simultaneously, move the cover in an upward direction, ensuring that the metal clips engage within their designated recesses on the logic board.

Step 61 | Place the lower connector cover

Step 61 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Employ tweezers for precise positioning of the lower connector cover's upper surface onto its designated location within the logic board.Ensure the lower connector cover is aligned correctly before setting it upon the press connector.
  • The placement of the lower connector cover necessitates careful alignment with the press connector to guarantee proper seating.

Step 62 | Install the cover screws

Step 62 image
Thumbnail 1
Thumbnail 2
  • Affix the 1.0 mm screw to fasten the central connector cover.
  • Secure the bottom connector cover using the pair of 1.3 mm screws.

Step 63 | Remove the final liners

Step 63 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Employ tweezers to securely grasp the protruding tabs located on each of the three blue adhesive liners, facilitating their removal to reveal the underlying adhesive.To ensure complete liner separation, it might be necessary to support the rear glass, preventing contact with the frame, specifically along the right-hand perimeter during the peeling process.
  • Complete adhesive exposure is achieved by carefully detaching the blue liners using the tweezers, ensuring the pull tabs are firmly held.

Step 64 | Place the back glass

Step 64 image
Thumbnail 1
Thumbnail 2

Position the replacement back glass over the device's frame, ensuring precise alignment.

Step 65

Step 65 image
Thumbnail 1
Thumbnail 2
  • Position the rear glass flat against the device frame, applying pressure to secure it with the retaining clips.
  • Ensure all fastening clips are properly connected by applying even pressure across the entire circumference of the rear glass.

Step 66 | Heat the back glass

Step 66 image
Thumbnail 1
Thumbnail 2
Enhancing the adhesive's effectiveness requires applying warmth to the back glass's borders with an iOpener, a hairdryer, or a heat gun, continuing until a tactile warmth is detected.A secure application of pressure around the back glass's outer boundary is necessary.
  • Employing screen vise clamps will reinforce the new adhesive's adhesion; otherwise, proceed to the following instructions for alternative securing methods.
  • Alternative techniques for maintaining the back glass's stability are detailed in the subsequent steps, should screen vise clamps be unavailable.

Step 67 | Press the back glass

Step 67 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
Achieving uniform pressure on an iPhone during repair, which reinforces the adhesion between the rear glass and the chassis, necessitates consideration of the camera module's protrusion.The original iPhone packaging, specifically the lid, can be utilized as a leveling platform when available.
  • Should the original packaging be unavailable, proceed to an alternative compression technique.
  • Position the iPhone, with the display facing upwards, within the box lid, ensuring the camera bump aligns with the designated indentation.
  • Locate an object with a height exceeding the box's sidewalls, but approximating the iPhone's width, and position it atop the device.
  • Subsequently, apply several substantial weights on top of the object to exert downward force.
  • Maintain this pressure for a minimum of thirty minutes; reduce the duration proportionally to the weight's mass, with overnight compression being optimal.

Step 68

Step 68 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
Absence of the original iPhone packaging necessitates an alternative procedure for uniform compression of the rear glass panel.To achieve consistent pressure distribution on the rear glass, proceed with the following three distinct actions.
  • Position the iPhone with its display facing downwards upon a cushioned, level work area.
  • Secure the rear glass surface with adhesive tape to safeguard its cosmetic appearance during the compression process.

Step 69

Step 69 image
Thumbnail 1
Thumbnail 2
Thumbnail 3
  • Position a single row of coins, or alternative items possessing comparable thickness, directly atop the adhesive tape situated along the perimeter of the rear glass.
  • The requisite number of coin layers will vary, contingent upon the individual thickness of each coin utilized.
  • Ensure uniform coin placement and a minimum thickness equivalent to the camera module's protrusion.

Step 70

Step 70 image
  • To apply downward force for screen separation, position several books or similarly weighty items atop the iPhone's chassis.
  • Because the pressure exerted by the iPhone could potentially mark the surface below, avoid utilizing precious or irreplaceable materials for this purpose.
  • Maintain the applied pressure for a minimum of thirty minutes; if the weighting objects are less substantial, extend this duration, with an overnight period being the optimal timeframe.

Step 71 | Install the pentalobe screws

Step 71 image
Thumbnail 1
Thumbnail 2
Utilize a P2 Pentalobe screwdriver for the subsequent operation.
Secure the device with two fasteners.Employ screws measuring precisely 7.8 millimeters in length.Position these screws symmetrically on both sides of the charging port.
Check COD Availability

Enter your pincode to see if Cash on Delivery is available in your area.

Please enter a valid 6-digit pincode