iPhone 1st Generation Camera Replacement
If camera replacement or removal is needed, or if mandated by your workplace, follow these steps.
Step 1 | SIM Card
Using a SIM card eject tool or a straightened paper clip, gently push into the aperture located adjacent to the headphone jack.
Using gentle, consistent pressure, depress the paper clip to eject the SIM card tray.
Using gentle, consistent pressure, depress the paper clip to eject the SIM card tray.
Step 2
Using your fingers, carefully extract the SIM card tray from the iPhone by sliding it outwards.
Step 3 | Antenna Cover
To detach the antenna cover, identify the two tabs and two catches positioned on its lower surface; specifically, depress the upper tabs inward, directing them against the black cover, to disengage their locking mechanism.
Step 4
Carefully insert the metal spudger in the space separating the antenna cover from the dock connector, avoiding direct contact with the connector.
Using a metal spudger, carefully separate the antenna cover from the silver front bezel by inserting the spudger into the space beside the dock connector and gently lifting upward, focusing near the two tabs to establish a slight separation.
Using a metal spudger, carefully separate the antenna cover from the silver front bezel by inserting the spudger into the space beside the dock connector and gently lifting upward, focusing near the two tabs to establish a slight separation.
Step 5
Using an iPod opening tool, gently separate the antenna cover from the front bezel by sliding the tool's wedge-shaped end into the space between them, ensuring the wedge faces the antenna cover.
Using the tool, maneuver it along the edge and advance it until it contacts the metal support.
Perform the identical steps again for the dock connector’s opposite side.
Using the tool, maneuver it along the edge and advance it until it contacts the metal support.
Perform the identical steps again for the dock connector’s opposite side.
Step 6
Apply firm, even pressure while sliding the antenna cover upwards, disengaging it from the iPhone’s sides. Should resistance be encountered, verify the cover is fully raised to release the retaining clips.
Step 7 | Case
Using a Phillips #00 screwdriver, detach the rear panel by unscrewing the three fasteners that hold it in place.
Step 8
Opening the iPhone requires patience and care; allocate sufficient time and remain calm to successfully complete this step.
Using a dental pick, proceed to the subsequent step by inserting it into the precisely sized, square aperture.
Using a dental pick, proceed to the subsequent step by inserting it into the precisely sized, square aperture.
Step 9
Carefully detach the rear panel, beginning on the side containing the control buttons.
Insert the dental pick fully into the square-shaped opening, potentially requiring slight manipulation and firm pressure for complete insertion.
Insert the dental pick fully into the square-shaped opening, potentially requiring slight manipulation and firm pressure for complete insertion.
Step 10
To release the rear panel, use a dental pick and apply a swift, rotational force—turning it counterclockwise—while pressing directly outward against the display assembly; rapid movement is preferable to avoid deforming the case.
Step 11
Carefully disengage the rear panel from the iPhone's casing by gently sliding a spudger between the panel and the device, focusing on the corner and top edges.
Step 12
Using the same steps, work on the opposite side of the iPhone; insert the dental pick fully into the designated square opening, and be prepared to gently maneuver the tool and use considerable pressure to ensure complete insertion.
Step 13
To release the rear panel, use a dental pick and apply a swift, rotational force—turning it clockwise—while pressing directly outward against the display assembly. Rapid movement is recommended to avoid deforming the case.
Because the headphone jack cable secures the rear panel to the iPhone, avoid completely detaching it at this stage.
Because the headphone jack cable secures the rear panel to the iPhone, avoid completely detaching it at this stage.
Step 14
Prior to detaching the headphone jack cable, ensure the device is powered down.
Employ a spudger to carefully separate the headphone jack cable connector from the logic board.
Employ a spudger to carefully separate the headphone jack cable connector from the logic board.
Step 15 | Camera
Carefully detach the camera connector using a spudger.
Step 16
Carefully extract the camera module from the iPhone, maintaining awareness of its delicate components.