iPhone 5c LCD and Digitizer Replacement
Employing our repair kit simplifies the screen replacement process; this streamlined guide details the steps for substituting the complete display assembly on your iPhone.
- Experienced users can utilize this guide to swap out the iPhone 5c's LCD and digitizer assembly, commonly referred to as the bare "front panel," which necessitates relocating the front-facing camera, earpiece speaker, LCD shield plate, and home button assembly from the old screen to the replacement.
- This procedure also details how to substitute the cable bracket that secures the front panel assembly.
Step 1 | Taping the display glass
To mitigate the risk of additional shattering and potential injury while repairing a cracked display glass, secure it with tape.
Apply strips of transparent packing tape across the iPhone screen, ensuring complete coverage by layering them until the entire display surface is protected.
To prevent glass fragments from scattering and maintain stability during the display separation process, this technique is essential.
To safeguard your eyes from potential glass fragments released during the repair process, always use safety glasses.
Apply strips of transparent packing tape across the iPhone screen, ensuring complete coverage by layering them until the entire display surface is protected.
To prevent glass fragments from scattering and maintain stability during the display separation process, this technique is essential.
To safeguard your eyes from potential glass fragments released during the repair process, always use safety glasses.
Step 2 | Removing the Pentalobe screws
To prevent a fire hazard or explosion due to potential puncture, ensure the iPhone's lithium-ion battery is depleted to less than 25% charge prior to continuing.
To prevent electrical shock or damage, ensure the iPhone is completely de-energized prior to starting the repair process.
Using appropriate tools, detach the two screws, each measuring 3.8 mm in diameter and featuring a P2 Pentalobe head, located on both sides of the Lightning connector.
To prevent electrical shock or damage, ensure the iPhone is completely de-energized prior to starting the repair process.
Using appropriate tools, detach the two screws, each measuring 3.8 mm in diameter and featuring a P2 Pentalobe head, located on both sides of the Lightning connector.
Step 3 | Starting the iSclack Opening Procedure
For users performing multiple repairs on iPhone 5, 5s, or 5c models, we suggest utilizing the iSclack to safely separate the device; those not employing this tool should proceed directly to Step 5.
Actuate the iSclack handle to release the clamping force of the suction-cup jaws.
Position the iPhone’s lower edge between the suction cups, ensuring it contacts the plastic depth gauge.
Position the uppermost suction cup so that it hovers slightly above the home button.
To secure the iPhone, position the suction cups centrally on both the front and rear surfaces, then activate the iSclack by opening the handles, which will separate the jaws, and apply firm pressure to both suction cups.
Actuate the iSclack handle to release the clamping force of the suction-cup jaws.
Position the iPhone’s lower edge between the suction cups, ensuring it contacts the plastic depth gauge.
Position the uppermost suction cup so that it hovers slightly above the home button.
To secure the iPhone, position the suction cups centrally on both the front and rear surfaces, then activate the iSclack by opening the handles, which will separate the jaws, and apply firm pressure to both suction cups.
Step 4 | Finishing the iSclack Opening Procedure
Grasp the iPhone firmly while operating the iSclack's handle to release the suction cups and lift the front panel away from the rear enclosure.
This specialized opening tool allows for controlled separation of the iPhone's components, preventing cable damage by limiting the degree of disassembly.
Detach the iPhone from its mounting surface by removing both suction cups.
Proceed directly to Step 8, bypassing Steps 4, 5, and 6.
This specialized opening tool allows for controlled separation of the iPhone's components, preventing cable damage by limiting the degree of disassembly.
Detach the iPhone from its mounting surface by removing both suction cups.
Proceed directly to Step 8, bypassing Steps 4, 5, and 6.
Step 5 | Manual Opening Procedure
Position a suction cup directly on the display surface, situated slightly higher than the home button's location.
Ensure full contact between the cup and the screen surface to guarantee a secure seal.
Ensure full contact between the cup and the screen surface to guarantee a secure seal.
Step 6 | Start lifting the front panel assembly
Verify secure adhesion of the suction cup to the front panel assembly.
Using one hand to secure the iPhone, lift the suction cup vertically to gently create a small gap between the front panel and the rear enclosure.
Exercise caution and use steady, even pressure when installing the display assembly, as its fit is significantly more snug than typical device components.
Using a plastic opening tool, carefully separate the rear case from the display assembly by gently levering it upwards, simultaneously lifting with a suction cup.
To release the front panel assembly from the rear case, carefully detach the multiple retaining clips, employing both the suction cup and plastic opening tool as needed.
Using one hand to secure the iPhone, lift the suction cup vertically to gently create a small gap between the front panel and the rear enclosure.
Exercise caution and use steady, even pressure when installing the display assembly, as its fit is significantly more snug than typical device components.
Using a plastic opening tool, carefully separate the rear case from the display assembly by gently levering it upwards, simultaneously lifting with a suction cup.
To release the front panel assembly from the rear case, carefully detach the multiple retaining clips, employing both the suction cup and plastic opening tool as needed.
Step 7
To detach the suction cup, extend the small plastic projection to break the airtight seal.
Detach the display assembly's suction cup.
Detach the display assembly's suction cup.
Step 8 | Opening up the phone
To expose the connectors located near the top edge of the device, gently raise the front panel, beginning at the home button end.
Carefully position the display at a 90-degree angle, then secure it in an upright position using a support to allow for hands-free access during the repair process.
As a temporary substitute, an unused, sealed can of soda can be employed to support the display.
To avoid stressing the display's wiring during the repair process, secure it with a rubber band.
Carefully position the display at a 90-degree angle, then secure it in an upright position using a support to allow for hands-free access during the repair process.
As a temporary substitute, an unused, sealed can of soda can be employed to support the display.
To avoid stressing the display's wiring during the repair process, secure it with a rubber band.
Step 9
Using a Phillips #000 screwdriver, detach the metal bracket that holds the battery connector by unscrewing the two 1.6 mm screws holding it in place on the logic board.
Step 10
Detach the bracket securing the battery connector using a tri-point screwdriver, ensuring no damage occurs to surrounding components.
Step 11 | Disconnecting the battery connector
Carefully lift the battery connector away from its corresponding socket on the logic board, employing a spudger or a similarly non-marring tool to avoid damage.
Exercise extreme caution when releasing the battery connector; lifting force should be applied solely to the connector, avoiding any pressure on the logic board socket or the board's surrounding components, as doing so risks socket destruction or damage to nearby parts.
Exercise extreme caution when releasing the battery connector; lifting force should be applied solely to the connector, avoiding any pressure on the logic board socket or the board's surrounding components, as doing so risks socket destruction or damage to nearby parts.
Step 12
Using a Phillips #000 screwdriver, detach the bracket that holds the front panel assembly cable by unscrewing the screws that fasten it to the logic board.
Use two screws, each measuring 1.3 millimeters.
A screw with a 1.7 mm head diameter is required.
A screw with a 3.25 mm diameter is required.
Carefully manage all screws during this procedure to ensure correct reassembly; improper screw selection, such as using a 3.25 mm screw or a 1.7 mm screw in the bottom right hole, will severely damage the logic board and prevent the device from powering on.
Avoid applying excessive force when tightening screws; if resistance is encountered during installation, verify that the correct screw size is being used and do not force the fastener.
Use two screws, each measuring 1.3 millimeters.
A screw with a 1.7 mm head diameter is required.
A screw with a 3.25 mm diameter is required.
Carefully manage all screws during this procedure to ensure correct reassembly; improper screw selection, such as using a 3.25 mm screw or a 1.7 mm screw in the bottom right hole, will severely damage the logic board and prevent the device from powering on.
Avoid applying excessive force when tightening screws; if resistance is encountered during installation, verify that the correct screw size is being used and do not force the fastener.
Step 13
Detach the bracket securing the front panel assembly cable to the logic board.
Step 14 | Disconnecting the front panel assembly cables
Carefully detach the front camera and sensor cable connector from its socket using a plastic pry tool or your fingernail.
Avoid applying force to the logic board socket while releasing the connector.
Avoid applying force to the logic board socket while releasing the connector.
Step 15
Prior to either detaching or reattaching the cables in this procedure, ensure the battery is disconnected.
Carefully detach the LCD cable connector by gently prying it apart with a plastic opening tool or fingernail.
Because the LCD and digitizer share a single cable assembly, lifting the LCD connector will simultaneously release both connections. Ensure both cables have completely separated before proceeding with display removal.
A disconnected LCD cable from its connector during reassembly can result in a blank screen or white lines appearing on the display; to resolve this, firmly reseat the cable and restart the device by briefly removing and reinstalling the battery.
Carefully detach the LCD cable connector by gently prying it apart with a plastic opening tool or fingernail.
Because the LCD and digitizer share a single cable assembly, lifting the LCD connector will simultaneously release both connections. Ensure both cables have completely separated before proceeding with display removal.
A disconnected LCD cable from its connector during reassembly can result in a blank screen or white lines appearing on the display; to resolve this, firmly reseat the cable and restart the device by briefly removing and reinstalling the battery.
Step 16 | Separating front panel assembly and rear case
Detach the front panel assembly from the rear case.
Step 17 | Home Button Ribbon Cable
Using a Phillips #000 screwdriver, detach the home button bracket from the display assembly by unscrewing the two 1.3 mm screws that hold it in place.
Step 18
Carefully lift the home button ribbon cable from the display assembly using a plastic opening tool.
Commence the process by addressing the contact points located on the right side, then proceed sequentially towards the left.
To prevent damage to the ribbon cable, begin the separation process on the left side and proceed rightward, as forceful movement could tear it. Initially, carefully lift the contacts from the front panel, as they are firmly attached.
To ease the plastic opening tool's passage beneath the contact points, if resistance is encountered, rotate the tool and apply slight pressure to the right edge of the contact cable to release the adhesive, then attempt insertion once more.
Commence the process by addressing the contact points located on the right side, then proceed sequentially towards the left.
To prevent damage to the ribbon cable, begin the separation process on the left side and proceed rightward, as forceful movement could tear it. Initially, carefully lift the contacts from the front panel, as they are firmly attached.
To ease the plastic opening tool's passage beneath the contact points, if resistance is encountered, rotate the tool and apply slight pressure to the right edge of the contact cable to release the adhesive, then attempt insertion once more.
Step 19
Carefully disconnect the ribbon cable that connects the home button to the display assembly.
During reassembly when replacing the home button ribbon cable, the metal bracket must be moved from the old cable to the new one.
During reassembly when replacing the home button ribbon cable, the metal bracket must be moved from the old cable to the new one.
Step 20 | Home Button
Using careful, even pressure, lift the upper-right section of the home button, separating it from the display assembly.
Partially depress the home button, stopping before it is fully disengaged, as a corner only needs to be exposed to allow for prying with a spudger.
Due to its delicate nature, the membrane is susceptible to tearing; should you encounter resistance while handling it, gently warm the area and attempt the process once more.
Partially depress the home button, stopping before it is fully disengaged, as a corner only needs to be exposed to allow for prying with a spudger.
Due to its delicate nature, the membrane is susceptible to tearing; should you encounter resistance while handling it, gently warm the area and attempt the process once more.
Step 21
Carefully detach the remaining adhesive securing the home button to the display surface using a spudger, applying gentle pressure.
Step 22
Carefully detach the home button assembly from the front panel.
Step 23 | Earpiece Speaker
Using a Phillips #000 screwdriver, detach the upper component bracket from the display assembly by unscrewing and removing the two screws that hold it in place.
A screw with a 4.2-millimeter head diameter is required.
A screw with a 2.3 mm diameter is required.
A screw with a 4.2-millimeter head diameter is required.
A screw with a 2.3 mm diameter is required.
Step 24
Carefully dislodge the earpiece speaker bracket from the display assembly by applying even pressure with the flat side of a spudger.
Step 25
Carefully detach the earpiece speaker component from the iPhone.
Step 26 | Front-Facing Camera and Sensor Cable
A light adhesive secures the front camera and its associated cable to the display assembly.
Applying heat with an iOpener, following the instructions provided for its use, will ease adhesive separation and prevent damage.
Although optional, performing this action helps prevent potential harm to the sensitive cable assembly.
Applying heat with an iOpener, following the instructions provided for its use, will ease adhesive separation and prevent damage.
Although optional, performing this action helps prevent potential harm to the sensitive cable assembly.
Step 27
Carefully lift the earpiece speaker contact cable using the tip of a spudger to release the adhesive securing the camera and sensor cable assembly.
The proximity sensor's operation depends on a critical, square component constructed from plastic and metal; this holder secures the sensor and ensures proper functionality.
When substituting the proximity sensor, ensure the holder stays affixed to the display's rear surface; should it detach with the removed sensor, separate it from the discarded component and secure it back onto the display using a minimal amount of adhesive.
The proximity sensor's operation depends on a critical, square component constructed from plastic and metal; this holder secures the sensor and ensures proper functionality.
When substituting the proximity sensor, ensure the holder stays affixed to the display's rear surface; should it detach with the removed sensor, separate it from the discarded component and secure it back onto the display using a minimal amount of adhesive.
Step 28
Using a spudger, gently pry the microphone upward from its molded position within the display assembly.
Step 29 | LCD and Digitizer
Using a Phillips #000 screwdriver, detach the four 1.2 mm screws—two on each side—that secure the LCD frame.
Step 30
Using a Phillips #000 screwdriver, detach the LCD shield plate by unscrewing the 1.6 mm screws.
Locate the screw positioned at the lower edge of the display assembly, close to the aperture for the home button.
Locate the fastener situated at the display's upper edge, close to the cable connections.
Locate the screw positioned at the lower edge of the display assembly, close to the aperture for the home button.
Locate the fastener situated at the display's upper edge, close to the cable connections.
Step 31
Carefully detach the LCD shield plate.Carefully detach the display assembly.
Step 32
The Display Assembly is still attached.