iPhone 5c Rear-Facing Camera Replacement
This document details the procedure for substituting a damaged rear camera assembly on an iPhone 5c.
Step 1 | Taping the display glass
To mitigate the risk of additional shattering and potential injury while performing the repair, secure the cracked display glass with tape.
Apply strips of transparent packing tape across the iPhone screen, ensuring complete coverage by slightly overlapping each strip.
To prevent scattered glass fragments and maintain stability during the display separation process, this technique is essential.
To safeguard your eyes from potential glass fragments released during the repair process, always use safety glasses.
Apply strips of transparent packing tape across the iPhone screen, ensuring complete coverage by slightly overlapping each strip.
To prevent scattered glass fragments and maintain stability during the display separation process, this technique is essential.
To safeguard your eyes from potential glass fragments released during the repair process, always use safety glasses.
Step 2 | Removing the Pentalobe screws
To prevent a potential fire or explosion hazard during repair, ensure the iPhone's lithium-ion battery is depleted to less than 25% capacity prior to beginning work; a fully charged battery poses a significant risk of ignition if damaged.
To prevent electrical shock or damage, ensure the iPhone is completely de-energized prior to starting the repair process.
Using appropriate tools, detach the two screws, each measuring 3.8 mm in diameter and featuring a P2 Pentalobe head, located on both sides of the Lightning connector.
To prevent electrical shock or damage, ensure the iPhone is completely de-energized prior to starting the repair process.
Using appropriate tools, detach the two screws, each measuring 3.8 mm in diameter and featuring a P2 Pentalobe head, located on both sides of the Lightning connector.
Step 3 | Starting the iSclack Opening Procedure
For those performing multiple iPhone 5, 5s, or 5c repairs, we suggest utilizing the iSclack to ensure safe separation; if you are not using this tool, proceed directly to Step 5.
Actuate the iSclack handle to release the clamping force of the suction-cup jaws.
Position the iPhone's lower edge between the suction cups, ensuring it contacts the plastic depth gauge.
Position the uppermost suction cup so it hovers slightly above the home button.
To secure the iPhone, position the suction cups centrally on both the front and rear surfaces, then activate the iSclack by opening its handles to release the clamping jaws and apply firm pressure.
Actuate the iSclack handle to release the clamping force of the suction-cup jaws.
Position the iPhone's lower edge between the suction cups, ensuring it contacts the plastic depth gauge.
Position the uppermost suction cup so it hovers slightly above the home button.
To secure the iPhone, position the suction cups centrally on both the front and rear surfaces, then activate the iSclack by opening its handles to release the clamping jaws and apply firm pressure.
Step 4 | Finishing the iSclack Opening Procedure
Using a firm grip on the iPhone, disengage the iSclack’s handle to release the suction cups, then lift the front panel away from the rear enclosure.
Using the iSclack allows for a controlled separation of the iPhone's components, preventing cable damage by only opening the device to the necessary extent.
Detach the iPhone from its mounting surface by removing both suction cups.
Proceed directly to Step 8, bypassing Steps 4, 5, and 6.
Using the iSclack allows for a controlled separation of the iPhone's components, preventing cable damage by only opening the device to the necessary extent.
Detach the iPhone from its mounting surface by removing both suction cups.
Proceed directly to Step 8, bypassing Steps 4, 5, and 6.
Step 5 | Manual Opening Procedure
Secure a suction cup to the display surface, positioning it directly over the home button area.
Ensure full contact between the cup's rim and the screen surface to guarantee a secure seal.
Ensure full contact between the cup's rim and the screen surface to guarantee a secure seal.
Step 6 | Start lifting the front panel assembly
Secure the front panel assembly to the suction cup, ensuring a strong and stable connection.
Using one hand to secure the iPhone, lift the suction cup vertically to gently create a small gap between the front panel and the device's back cover.
Exercise caution and use steady, even pressure when installing the display assembly, as its fit is considerably more snug than typical device components.
Using a plastic opening tool, carefully separate the rear case from the display assembly by gently levering it upwards, simultaneously lifting with a suction cup.
To release the front panel assembly from the rear case, carefully disengage the multiple retaining clips, potentially requiring the coordinated use of both a suction cup and a plastic opening tool.
Using one hand to secure the iPhone, lift the suction cup vertically to gently create a small gap between the front panel and the device's back cover.
Exercise caution and use steady, even pressure when installing the display assembly, as its fit is considerably more snug than typical device components.
Using a plastic opening tool, carefully separate the rear case from the display assembly by gently levering it upwards, simultaneously lifting with a suction cup.
To release the front panel assembly from the rear case, carefully disengage the multiple retaining clips, potentially requiring the coordinated use of both a suction cup and a plastic opening tool.
Step 7
To detach the suction cup, extend the small plastic projection to break the airtight connection.
Detach the display assembly's suction cup.
Detach the display assembly's suction cup.
Step 8 | Opening up the phone
To expose the connectors located at the top edge of the device, gently raise the front panel, starting from the home button area.
Carefully position the display at a roughly 90-degree angle, then secure it in an upright position using a support to prevent movement during the repair process.
As a temporary measure, an unused, sealed can of soda can substitute for the display during the repair process.
To avoid stressing the display's wiring during the repair process, secure it with a rubber band.
Carefully position the display at a roughly 90-degree angle, then secure it in an upright position using a support to prevent movement during the repair process.
As a temporary measure, an unused, sealed can of soda can substitute for the display during the repair process.
To avoid stressing the display's wiring during the repair process, secure it with a rubber band.
Step 9
Using a Phillips #000 screwdriver, detach the metal bracket that holds the battery connector by unscrewing the two 1.6 mm screws it uses to fasten to the logic board.
Step 10
Detach the bracket securing the battery connector using a tri-point screwdriver.
Step 11 | Disconnecting the battery connector
Carefully lift the battery connector away from its corresponding socket on the logic board, employing a spudger or a clean fingernail to avoid damage.
Exercise extreme caution when releasing the battery connector, ensuring force is applied solely to the connector and not the logic board socket; applying pressure to the socket or the logic board risks socket destruction or damage to adjacent components.
Exercise extreme caution when releasing the battery connector, ensuring force is applied solely to the connector and not the logic board socket; applying pressure to the socket or the logic board risks socket destruction or damage to adjacent components.
Step 12
Using a Phillips #000 screwdriver, detach the cable bracket from the logic board by unscrewing all the screws that hold it in place.
Use two screws, each measuring 1.3 millimeters.
A screw with a 1.7-millimeter head diameter is required.
A screw with a 3.25 mm diameter is required.
Carefully note the location of each screw during this stage, as incorrect placement during reassembly can cause serious harm. Substituting a 3.25 mm screw or a 1.7 mm screw into the bottom right hole will severely damage the logic board, preventing the device from powering on.
To prevent damage, avoid applying excessive force when tightening screws; if resistance is encountered during installation, verify that the correct screw size is being used and do not force the fastener.
Use two screws, each measuring 1.3 millimeters.
A screw with a 1.7-millimeter head diameter is required.
A screw with a 3.25 mm diameter is required.
Carefully note the location of each screw during this stage, as incorrect placement during reassembly can cause serious harm. Substituting a 3.25 mm screw or a 1.7 mm screw into the bottom right hole will severely damage the logic board, preventing the device from powering on.
To prevent damage, avoid applying excessive force when tightening screws; if resistance is encountered during installation, verify that the correct screw size is being used and do not force the fastener.
Step 13
Detach the bracket securing the front panel assembly cable to the logic board.
Step 14 | Disconnecting the front panel assembly cables
Carefully detach the front camera and sensor cable connector from its socket using a plastic pry tool or your fingernail.
Avoid applying lifting force to the logic board socket itself; direct all prying action solely to the connector.
Avoid applying lifting force to the logic board socket itself; direct all prying action solely to the connector.
Step 15
Prior to either detaching or reattaching the cables in this procedure, ensure the battery is completely disconnected.
Carefully detach the LCD cable connector by gently prying it free with a plastic opening tool or fingernail.
Because the LCD and digitizer share a single cable assembly, lifting the LCD connector will simultaneously release both connections. Ensure both cables are completely detached prior to display removal.
If the display shows a blank screen or white lines after reassembly, the LCD cable might have become disconnected from its connector; to resolve this, firmly reseat the cable and restart the device by briefly removing and reinstalling the battery.
Carefully detach the LCD cable connector by gently prying it free with a plastic opening tool or fingernail.
Because the LCD and digitizer share a single cable assembly, lifting the LCD connector will simultaneously release both connections. Ensure both cables are completely detached prior to display removal.
If the display shows a blank screen or white lines after reassembly, the LCD cable might have become disconnected from its connector; to resolve this, firmly reseat the cable and restart the device by briefly removing and reinstalling the battery.
Step 16 | Separating front panel assembly and rear case
Detach the front panel assembly by disengaging it from the rear case.
Step 17 | Rear-Facing Camera
Using a Phillips #000 screwdriver, detach the rear case from the rear-facing camera by unscrewing the two 1.5 mm screws that hold it in place.
Step 18
Detach the bracket securing the rear camera assembly.
Step 19
Carefully lift the rear-camera connector from the logic board using the flat side of a spudger.
Step 20
Carefully detach the iPhone's rear camera assembly.