iPhone 6s Plus Earpiece Speaker Replacement

• To prevent potential hazards and damage, ensure the battery's charge level is reduced to less than 25% prior to beginning the disassembly process.A lithium-ion battery must be fully charged.A puncture can result in fire and/or explosion.
• To prevent electrical shock or damage, ensure the iPhone is completely de-energized prior to starting the repair process.
• Using a Pentalobe screwdriver, detach the pair of 3.4 mm screws located on both sides of the Lightning connector.

• For those utilizing the Anti-Clamp tool, the following two steps detail its use to simplify the opening process; otherwise, proceed to the instructions three steps further down for an alternative approach.
• Refer to the detailed user manual for comprehensive guidance on operation.Employ an anti-clamp device.Consult this resource for detailed instructions.
• To release the Anti-Clamp's arms, move the blue handle in a rearward direction.
• Position the arms so they clear the left or right side of the iPhone, then move them into place.
• Affix two suction cups, one to the front and one to the rear surface of the iPhone, placing them close to the lower edge, directly above the home button.
• Apply vacuum by pressing the cups firmly against the surface needing treatment.
• To improve the Anti-Clamp's grip on your iPhone if the exterior feels excessively smooth, apply adhesive tape to the device's surface.

• To secure the arms, advance the blue handle in the direction indicated.
• Rotate the handle fully, completing a 360-degree turn, observing for the initial signs of cup expansion.
• Maintain parallel positioning of the suction cups; should misalignment occur, gently release the suction cups' grip and reposition the arms.
• Once sufficient separation is achieved by the Anti-Clamp tool, slide a prying tool beneath the display.
• To ensure adequate separation, reposition the handle by 90 degrees.
• Apply adjustments in increments not exceeding 90 degrees, pausing for several seconds after each adjustment to allow the Anti-Clamp device to function and the system to stabilize.

• Ensure availability of a 3/8-inch socket wrench before proceeding.Prevent clamping.To operate the suction handle, proceed with the following sequence of actions.
• Using a hair dryer or iOpener, gently warm the bottom perimeter of the iPhone's enclosure with moderate heat for approximately 60 seconds.
• Applying heat will loosen the adhesive that holds the display in place, facilitating separation.

• Removing the 6s Plus display will release a perimeter adhesive strip; replacement adhesive strips should be prepared beforehand if desired. Functionality remains unaffected whether the adhesive is replaced or not.
• Using a suction cup, secure the lower left portion of the display assembly.
• To facilitate suction cup attachment when the display has severe cracking, apply a sheet of clear packing tape across the damaged area; as an alternative, a robust adhesive tape can be substituted for the suction cup. Should these methods prove ineffective, secure the suction cup directly to the fractured screen using superglue.

• Apply steady, even force to lift the suction cup, generating a small separation between the front panel and the rear case.
• To avoid display assembly damage, use minimal force when separating it from the rear case; the goal is to create a narrow separation.

• To avoid damage, begin separating the front panel by gently levering it away from the chassis at the indentation located directly over the headphone jack.
• Using continuous suction from the cup, carefully slide the spudger's flat end into the opening situated immediately over the headphone jack.

• Using a spudger, gently increase the space separating the front panel from the rear case.

• Using a screwdriver with a flat tip, carefully slide it into the slot.Use a plastic pry tool to access.Locate the component along the display's right side.
• Carefully position theUse a plastic pry tool, often referred to as a spudger, to avoid scratching surfaces.Raise the component along the right-hand vertical plane.

• Employ a 3/8-inch socket wrench to tighten the fastener to a torque of 15 Nm, ensuring proper engagement and preventing damage to the component.Use a plastic pry tool.Maintain pressure on the rear case while lifting with the suction cup to release the phone.
• Carefully detach the display from its surrounding components, but ensure it remains connected; full removal is prohibited.Carefully avoid stressing the display's upper edge, as doing so risks harming the data cables located there.

• Carefully raise the display assembly, utilizing the front panel's top clips as a pivot point to access the phone's interior.
• Carefully separate the display assembly from the device housing, creating a gap of approximately 1 millimeter.Rotate to a 90-degree angle.To maintain stability during the repair process, position the device at an incline and secure it with a support.
• To prevent damage, limit display exposure during the repair process.Ensure the angle is precisely 90 degrees.Care must be taken during separation as the display, digitizer, and front camera remain linked to the phone’s upper portion via delicate cables prone to damage.
• To avoid stressing the display's wiring during the repair process, secure it with a rubber band.
• As a temporary measure, an unopened, sealed can of soda can provide the necessary support for the display.

• Detach two.Employ a Phillips head screwdriver.Fasten the battery connector bracket to the logic board using screws of the specified lengths.
• Begin the process by executing the singular action.Use a 2.9-millimeter screw.
• Begin the process by executing the action designated as "One."Use a screw with a diameter of 2.3 millimeters.
• To prevent irreversible damage, meticulously organize all screws during disassembly, ensuring each is returned to its original location during reassembly.

Employ a 5/32-inch hex key to tighten the retaining screw to a torque of 6-8 inch-pounds, ensuring the component is securely fastened and avoiding over-tightening which could damage the threads.Use a spudger.Use a clean fingernail or similar tool to detach the battery connector from the logic board, ensuring it is lifted vertically.

To prevent unintended activation, carefully reshape the connector and then test the iPhone's power functionality during the repair process.

• Take out the listed components.Use a Phillips head screwdriver.:
  
  • Use three screws, each measuring 1.3 millimeters.
  • A screw with a 1.6 mm head diameter is required.
  • A screw with a 3.0 mm diameter is required.

Ensure proper alignment and secure placement of this component during the reassembly process.Use a screw with a diameter of 3.0 millimeters.Ensure the component is positioned precisely in the upper-right quadrant of the bracket; incorrect placement risks logic board damage.

Using a T5 Torx screwdriver, detach the display cable bracket.

• Avoid applying force to the logic board socket while releasing the connector; focus your prying action solely on the connector.
• Employ a 3/8-inch socket wrench to loosen the retaining bolt, ensuring you maintain a firm grip and wear safety glasses to protect against potential debris; subsequently, carefully detach the component.Use a plastic pry tool.Carefully detach the connector securing the front camera and its associated sensor cable.

• Employ a 3/8-inch socket wrench to loosen the retaining bolt, ensuring you maintain a firm grip and wear safety glasses to protect against potential debris; torque the bolt to 18 Nm upon reinstallation.Use a plastic pry tool.Using a prying tool, carefully lift the digitizer cable directly upward to release it from its connector on the logic board.
• To ensure proper alignment and prevent damage, avoid applying pressure to the connector's middle when reattaching the digitizer cable; instead, gently secure it by pressing on each end sequentially. Central pressure risks warping the component.The display's touch functionality is impaired due to physical harm to the digitizer..

• Prior to either detaching or reattaching the cable in this procedure, ensure the battery is disconnected.
• Using a prying tool, carefully release the home button/fingerprint sensor cable by lifting it vertically from its connector on the logic board.

• Carefully detach the display assembly, ensuring no damage occurs.
• If you intend to substitute fresh adhesive along the display's perimeter during reassembly, stop at this point.

• Detach the specified trio.Use a Phillips head screwdriver.:
  Use two screws, each measuring 2.7 millimeters.
  A screw with a 1.4 mm diameter is required.

Detach the speaker bracket from the earpiece assembly.

Carefully employ the tool's flat end toUse a plastic pry tool, often referred to as a spudger.Raise theThe front-facing camera for video calls is referred to as the FaceTime camera.Carefully extract the component from its enclosure.

Grasp and extract theThe front-facing camera used for FaceTime video calls.Detach the earpiece speaker from its position.